New Ultrasonic Cleaner

Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester


Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester
Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester
Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester
Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester
Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester

Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester    Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester

Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester. CNC-602A is an advanced electromechanical product, which can clean and test injectors by simulating engine working conditions. It can also perform cleaning on the injectors and fuel supply system on vehicle. Why have to clean injector. When we turned off the engine suddenly, the gasoline which have been spray out can not be recycled.

It would attached on the injector and combustion chamber walls. Gasoline is easy to volatile, but wax and varnish were stayed. Heat these wax and varnish day after day, they will be changed into hard coke.

The hard coke will be produced more quickly and more thickly when engine work with poor quality fuel. The hard coke lead 4 problems on injector. So we have to clean injector and engine system. Do not get any cleaning solvent on the outside of the vehicle, as this will damage the paint.

A heavily clogged fuel injector may not allow enough cleaner to pass through during a routine cleaning to be adequately cleaned. Additional cleanings may be needed to clear heavy deposits. Launch CNC602A is 6-cylinder fuel injector cleaning machine (with 6 tubes), and it can clean and test six injectors as same time. If 4-cylinder engine, when use the CNC602A to clean and test 4 injector(there are 2 connector in machine should be stoppered).

Eight-cylinder engine, when you use CNC602 do clean the test, you should do clean the test twice per four injector. The machine work on petrol injector, not for diesel injector. CNC602A only have 220 Volt. This machine was for 6-cylinder car.

Block 2 tube for 4 jar car. Item fit for two kinds of injectors.

Top feed injector accessories were standard configure. Side feed injector accessories for option. Support no dismantle clean car fuel system. Need additional connector kits, not include in the price, need to add 80USD to get it. The machine fit for most of petrol injector(come with lost of adapters), but not for diesel injector. CNC-602A is an advanced electronic mechanical product, which can clean and test injectors by simulating engine working conditions. Launch CNC602A Features & Functions.

Ultrasonic Cleaning: Perform simultaneous cleaning on several injectors and remove the carbon deposits on the injectors completely. Uniformity/ Sprayability Test: Test the uniformity each injector, and monitor the spraying status of each injector with the help of backlight.

This test is also for reverse flush. Leakage Test: Test the sealing and dribbling conditions of injectors under system pressure.

Injecting Flow Fest: Check the injecting amount of 15 seconds constant injection. Auto Test: Test injectors by simulating different working conditions.

On-vehicle Cleaning: The unit is equipped with various adaptors and couplers that facilitate cleaning injectors on vehicle. Audi, Australia Ford, Benz, BMW, Brilliance, Chevrolet, Chevy, Chrysler, Citroen, Dacia, Dadi, Daewoo, Daihatsu, Demo, Fiat, Ford, GM, Holden, Honda, Hyundai, Isuzu, Jaguar, Kia, Lancia, Land Rover, Mahindra, Maruti, Mazda, Mitsubish, Nissan, Opel, Peugeot, Porsche, Renault, Romeo, Rover, Saab, Seat, Skoda, Smart, Subaru, Suzuki, Tata, Toyota, Volvo, VW, Yamaha. Power supply: AC220V±10%, 50/60Hz; 50/60Hz. Simulated RPM range: 109990rpm; step: 10rpm. Pulse width: 0.525ms; step 0.1 ms.

1 Cleaning hard coke from injector via ultrasonic and auto electronic technology. 2 Imitate working as vehicle's fuel system. 3 Washable testing single-point injection as TBI, CFI, ECI and CIS.

7 Fuel injection quantity detector. 11 The minimum pulse width test. CNC-602A Spare Parts &Package List.

1 x CNC602A Main Machine. 201020068 6-cylinder fuel distributo kits. 103250014 Adaptor for fuel top-supply injector.

103250028 Stopper for fuel distributor. 103230107 Adjusting pole for reverse flush.

103250013 Adaptor for fuel top-supply injector. 103250015 Swiss thread adaptor for fuel top-supply injector.

103250016 Coarse thread adaptor for fuel top-supply. 105020217 pulse signal connection cable 1. Be used for the connection. Of special injector, T=0.5. 105020218 pulse signal connection cable 2.

Of special injector, T=0.8. 101020131 6-cylinder Injector pulse signal cables. 104130024 Lots of different O rings. If your package delayed few days, due to any unexpected factor, please wait patiently.

Your kindly understanding and great patience would be highly appreciated! Please do not hesitate to leave us your 5 Star. Thank you for your kindness. We are reliable supplier to both wholesalers and retail sellers. And we are a professional Authorized dealers of.

Also offer reasonable prices , excellent customer service and a reliable credit standing are our target! We supply many products on Automobile consumer. We have OBDII cars / Light Trucks / Heavy Duty Truck's. Battery Tester, Fuel Injector Cleaner Machine , Smoke Leak Detector Machine, Digital Circuit Tester, lgnition Spark Tester , Engine Timing Tool. And much more others products.

Wish we can solve the problem peacefully. We will reply you within 12 hours and do our best solve the problem with you Except on Weekends and. The item "Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester" is in sale since Sunday, June 28, 2020. This item is in the category "Vehicle Parts & Accessories\Garage Equipment & Tools\Diagnostic Equipment & Tools\Code Readers & Scanners".

The seller is "beherenow177" and is located in Shenzhen. This item can be shipped worldwide.

  1. Brand: LAUNCH
  2. Manufacturer Part Number: CNC602A
  3. Warranty: 3 Year
  4. Country/Region of Manufacture: China
  5. Item Weight: 33 KG
  6. Language:: English
  7. Type: fule injector cleaner tester
  8. Feature1: Support Uniformity Sprayability Leakage Test
  9. Feature2: Support 4/6 cylinder injector Test
  10. Feature3: Support almost all 12V car petrol injector
  11. Vehicle Type: Motorcycle


Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester    Original LAUNCH Auto CNC602A Car Fuel Injector Ultrasonic Cleaner Machine Tester